Sale!

The new eBox Ethernet Remote Control Device for ACOM power amplifiers .

567.00

Ships in 5/7 days

Available on backorder

Description

  • COM eBox Key Characteristics
    • Remote Control Capabilities via Ethernet
    • Suitable for Use with ACOM 600S, 700S, 1200S and 2000A Power Amplifiers
    • Web-Browser Based User Friendly Interface

    ACOM eBox Main Features

    • ETHERNET CONNECTIVITY

    eBox is an active Ethernet device which directly integrates ACOM HF power amplifiers to the Ethernet networks. The ACOM eBox is specifically designed and developed for remote control exclusively of the following ACOM HF power amplifiers:

    • ACOM 600S
    • ACOM 700S
    • ACOM 1200S and
    • ACOM 2000A with RCU (remote control unit).

    The eBox receives amplifier’s specific commands via Ethernet interface and forwards them to the ACOM amplifier.

    • EASY to OPERATE

    The administration of the eBox is done via Web-based programming interface specially developed for ACOM amplifiers. You can use any personal computer running any operating system. You just need to run web browser as Chrome, Opera, Firefox, MS Edge, Safari, etc.

     

    • ALWAYS UP-TO-DATE

    Your eBox is always up-to-date due to its integrated function for firmware update. The newest firmware versions are available (usually as *.bin files) at www.acom-bg.com. With just a few clicks you can upload a new firmware to the eBox.

Additional information

Weight1.0 kg
SPECIFICATIONS

Frequency coverage: 1.8 to 30MHz and 50 to 54MHz, continuously (30 to 50MHz on request).
Antenna impedance matching capability: all impedances with 50 Ohm-SWR between 1:1 and 3:1; (for some higher-SWR impedances matching is also possible see power limitations below).
Maximum RF Input power admissible, average or continuous (no mode limitations; in brackets – PEP):
SWR

1-3:1

3.5:1*

4:1*

5:1*

7:1*

10:1*

Pin, W

1200

900

700

500

300

200

* (when tuning is possible for SWR above 3:1)

Rem: Operation at SWR above 10:1 is not permitted even though matching could be possible in some cases.
RF Input characteristics:
-Nominal impedance: 50-Ohm unbalanced;

-Connector type: UHF/PTFE (S0239A);

-Input SWR during full tuning (basic matching cycle): below 2:1

-Input SWR soon after full tuning: less than 1.5:1 (below 1.3:1 typ.).

Antenna output characteristics:
-Nominal impedance: 50-Ohm unbalanced;

-Connector type: UHF/PTFE (S0239A);

-Number of outputs – 4;

-Antenna SWR: between 1:1 and 3:1 for 100% matching, full power; for higher-SWR impedances (provided matching is possible) see power limitations above).

Full tuning duration (basic matching cycle):
-Below 10MHz: less than 5s (2-3s typ.)

-Above 10MHz: less than 3s (1-2s typ.).

RF Input power required during full tuning: 25W +3/-3 dB (12.5 to 50 W), non-modulated.
Power supply and control: available from the ACOM solid state HF+6m amplifiers through RF-output coaxial cable; +26VDC, up to 25 W consumption; control data using a FSK modem at 60 kHz.
Coaxial cable maximum length (same for RF power, DC power supply, and control):
-100 m (330 feet) for cable type RG-213.

Size and mass (operating)

– Width: 345mm (13.6”)

– Depth: 250mm (9.9”)

– Height: 190mm (7.5”)

– Mass: 4.2kg (9.25lbs).

Operating environments:
-Weather protection: IP 53 (NEMA Type 3);

-Temperature range: -40 to +65 degrees C (-40…+150F);

-Humidity: up to 98% @ +40 degrees C (104F);

-Height ASL without parameters deterioration: up to 3050 m (10 000 feet).

MANUAL

https://acom-bg.com/sites/default/files/manuals/ACOMeBoxUserManualGB10_2021.pdf

Reviews

There are no reviews yet.

Be the first to review “The new eBox Ethernet Remote Control Device for ACOM power amplifiers .”

Your email address will not be published. Required fields are marked *